Auto routing

Tap a destination.
Get a smart route.

SeaVectors reads the official ENC charts the way a careful navigator would — depths, rocks, wrecks, fairways and bridges — and plans a route around your boat. Here’s how it decides.

Free for 1 month, then $29.99/year or $5.99/month. Cancel anytime.

Watch full recordings

Real passages planned and run in SeaVectors on iPad, start to finish.

Five steps, every time

  1. 1

    Your boat

    Draft, under-keel clearance and height set what water and bridges you can use.

  2. 2

    Read the charts

    Depth areas, dredged channels, land, rocks, wrecks, fairways and one-way lanes.

  3. 3

    Find usable water

    Shallow water, hazards and the shoreline are ruled out, with a safety margin.

  4. 4

    Choose the best path

    Fairways first, then the starboard side, then the shortest way.

  5. 5

    Check and review

    Every shortcut is re-checked; then you review shallow spots, chart notices and the forecast.

It starts with your boat

Enter your boat once in My Boat. Every route is calculated — and saved — with those numbers.

Draft+Under-keel clearance=Routing depth
Height above waterline+Overhead margin=Bridge clearance

Routing depth

Water is usable only where the chart’s minimum depth meets your routing depth. A 2–5 m depth area counts as 2 m. Extra depth isn’t rewarded on its own — 4 m and 10 m water both pass a 3 m boat equally.

Bridges

With your height set, every charted bridge is checked against its closed clearance. Missing or insufficient clearance blocks the way, and SeaVectors never assumes a drawbridge will open.

How it reads the chart

The official ENC vector chart is turned into a fine grid of cells. Each cell becomes water, shallow, land, hazard or unknown.

Depths

Depth areas and dredged channels are combined, and where they overlap the shallower value wins. Unknown depth is never treated as deep.

Rocks, wrecks, obstructions

Blocked with a 40 m buffer — unless the chart gives a surveyed depth of good quality that, after its uncertainty, still clears your routing depth.

Shoreline margin

The route keeps clear of land, shallows and unknown water, and is drawn gently away from their edges, not just from the coastline.

Long trips are planned in two passes: a fast overview finds the corridor, then each section is calculated in full detail.

Fairways first. Then starboard.

Among all the safe paths, SeaVectors picks the one a careful skipper would take — in strict order, so saving distance can never buy a worse position.

FAIRWAY Starboard half Rock · 40 m buffer centreline
  1. Stay in the fairway. Time outside charted fairways and dredged channels is minimised first, so a longer route inside the fairway beats a shortcut across it.
  2. Keep to starboard. Within a channel, the route holds the starboard side of the safe water — measured from the edge of water deep enough for your boat, not just the painted chart line.
  3. Then the shortest way. Only after those does distance decide, with a gentle pull away from shoals and banks.

One-way lanes

Charted recommended tracks with a direction are obeyed — the route never runs against a one-way lane.

Junctions

At side branches the main channel is followed straight through, instead of bending toward the branch mouth and back.

Marinas and docks

A short, checked approach of up to 3 km lets you leave or reach a dock beside the channel without a detour to a distant entrance.

What the route colours mean

When the ideal route isn’t possible, SeaVectors tells you exactly where and why, instead of quietly failing or hiding it.

Normal route

Meets your routing depth and the full shoreline and hazard margins.

Red · shallow or narrow

Known charted water below your routing depth, or a narrow pass with a reduced 10 m shoreline margin (each under 300 m, 500 m in total). Check it before you go.

Amber · drying approach

A dock or arrival approach over water charted at 0 m.

Purple · local approach

A checked approach to a dock that’s closer to shore than the normal margin allows.

Never through land, a pontoon, unknown or negative depth, or a blocking hazard — no exception applies to those.

Then you review it, leg by leg

Shallow spots

Every red section lists the charted depth next to your routing depth, so you can judge it against the tide.

Chart notices

Restricted areas, caution areas, traffic separation, cables and fishery closures near the route are gathered in one list.

Forecast along the way

Wind, gusts, waves, current and thunderstorms are sampled every 15 minutes of travel at your cruising speed, and flagged above 20 kn wind, 25 kn gusts, 1.5 m waves or 2 kn current.

Edit freely

Drag a waypoint or add a stop, and only the changed stretch is recalculated and re-checked. Anything you place yourself stays exactly where you put it.

Simulate first

Play the route through before you leave and watch the boat and its instruments move along it.

What it doesn’t do

Auto routing is a planning aid built on charted information. It doesn’t replace a proper lookout or your own judgement.

Plan your next passage.

Every feature in one plan, with your first month free.

Yearly Save 58% Limited time

$29.99/year

Just $2.50 a month

Monthly

$5.99/month

Cancel anytime

Start your free month

See every feature Weather models Compare apps